Prominent Trade Universal Undercoat

An excellent quality alkyd based undercoat.

Description

[jbutton size=”large” link=”http://www.masters.co.zw/wp-content/uploads/2014/11/msds_prominent_trade_universal_undercoat.pdf” newpage=”yes”]View Datasheet[/jbutton]

Purchase:
Prominent Trade Universal Undercoat is available in the following sizes: and 5lt

Appearance: Matt
Spreading Rate: 8 – 10 m²/litre depending on surface texture and porosity.
Solids: 67% by mass; 47% by volume.
Density: ± 1.5 kg/litre.
Recommended Dry Film Thickness: 50 – 60 µm per coat minimum.
Viscosity: ± 105Kµ.
Flash Point: 43°C.

Storage:

  • Keep containers properly sealed.
  • Store away from direct heat, sun and severe cold in a place with adequate ventilation.

Available Sizes: 5Lt
Colours: White

Respecting The Environment:

  • 100% Lead Free.
  • Dispose of excess product and containers in a responsible manner without harming the environment.
  • This product is manufactured under strict SABS ISO 9001 quality standards.

Features

  • Provides a smooth base for topcoats.
  • Easy brushing and levelling.
  • Excellent adhesion on properly primed or sealed surfaces.
  • Easily sanded for smoother finishes.
  • 100% lead free.

Intended Usages

  • As an undercoat on interior/exterior primed metal, interior wood or hardboard.
  • For use as a basecoat over correctly primed plaster followed by Prominent Gloss Enamel or Prominent Eggshell Enamel.

Application Details

  • Mixing: Stir before use with a flat paddle to an even consistency. Stir occasionally during use.
  • Method: Roller or brush.
  • Thinning: ProGold Mineral Turpentine.
  • Cleaning: Remove as much of the product as possible from the application equipment before cleaning with ProGold Mineral Turpentine.

Conditions:

  • Temperature between 5°C and 40°C.
  • Relative humidity of less than 85%, preferably between 10: 00 and 16: 00.
  • Ideally apply when the temperature of the substrate is at least 2°C above dew point. If possible away from direct sunlight.

Drying time:
Surface dry:  3 hours, Hard dry:  14 hours at 23°C.
Note:  Higher temperatures will accelerate the drying times (approximately halved for every 10°C increase), whilst lower temperatures will retard the drying time (approximately doubled for every 10°C decrease).

Recoating time: 18 hours.
Requirements: One coat.

Surface Preparations
Metal (new):

  • Clean surface with ProGold General Purpose Cleaner/water mixture (1: 5) and scouring pads, rinse with clean water and allow to dry.
  • Prime with Prominent Machinery Enamel Primer or Prominent Rust Primer.

Metal (rusted):

  • Remove rust, clean surface with ProGold General Purpose Cleaner/water mixture (1: 5) and scouring pads, rinse with clean water and allow to dry.
  • Prime with Prominent Rust Primer.

Wood:

  • Sand smooth, remove dust and prime with Prominent Wood Primer.

Hardboard:

  • Apply directly.

Cement Plaster:

  • Prime with Prominent Dampcure or Prominent Trade Plaster Primer or Prominent Plaster Primer.

Rhinolite:

  • Prime with Prominent Plaster Primer or Prominent Trade Plaster Primer.

Emulsion Paint:

  • Clean and apply directly.

Enamel Paint:

  • Abrade and apply directly.

Paint in poor condition:

  • Remove and treat as new work.

Limitations

  • Cannot be applied to unprimed surfaces.
  • Must be overcoated for protection.

Safety

  • Keep out of reach of children.
  • Ensure to maintain good ventilation during application and drying process.
  • In case of skin contact, wash with soap and water or a recognised skin cleaner. Avoid contact with eyes. In case of contact with eyes rinse immediately with running water and seek medical advice.
  • If product is ingested drink plenty of water or milk. Do not induce vomiting at any time. Seek medical advice.
  • Refer to the Material Safety Data Sheet (MSDS) for detailed information about the product and transportation and classification criteria. MSDS is available on www.prominentpaints.co.za or from Prominent Customer Service Department.
  • To avoid any risk of spillage, always transport in a secure upright position.
  • Keep out of reach of children.
  • Ensure to maintain good ventilation during application and drying process.
  • In case of skin contact, wash with soap and water or a recognised skin cleaner. Avoid contact with eyes. In case of contact with eyes rinse immediately with running water and seek medical advice.
  • If product is ingested drink plenty of water or milk. Do not induce vomiting at any time. Seek medical advice.
  • Refer to the Material Safety Data Sheet (MSDS) for detailed information about the product and transportation and classification criteria. MSDS is available on www.prominentpaints.co.za or from Prominent Customer Service Department.
  • To avoid any risk of spillage, always transport in a secure upright position.

Reviews

There are no reviews yet.

Be the first to review “Prominent Trade Universal Undercoat”

Your email address will not be published. Required fields are marked *

five × 1 =