Description

Purchase:
Prominent Fillercoat is available in the following sizes: and 20lt

Appearance: Matt
Spreading Rate: 3 – 6 m²/litre dependent on surface texture and porosity.
Solids: ± 50% by mass and ± 30% by volume.
Density: ± 1,53 kg/litre.
Recommended Dry Film Thickness: 1 coat at 40 µm minimum.
Viscosity: ± 110 Kµ.
Flash Point: Non-flammable.

Storage:

• Keep containers properly sealed.
• Store away from direct heat, sun and severe cold in a place with adequate ventilation.

Available Sizes: 20lt
Colours: White

Respecting The Environment:

• 100% Lead Free.
• Dispose of excess product and containers in a responsible manner without harming the environment.
• This product is manufactured under strict SABS ISO 9001 quality standards.

Features

• Waterbased: Low odour, easy cleaning.
• Alkali resistance: Can be applied directly to new cement plaster.
• Excellent sealing: Prevents absorption of more expensive final coats by substrate.
• Economical: Good obliteration at low cost.
• 100% lead free.

Intended Usages

• Mainly as a base coat for subsequent PVA finishes on new interior and exterior plastered walls.
• Gypsum ceilings.

Application Details

• Mixing: Stir thoroughly with a flat paddle to an even consistency. Stir occasionally during use.
• Method: Roller, brush or airless spray.
• Thinning: Not recommended.
• Cleaning: Remove as much of the product as possible from the application equipment before cleaning with water.

Conditions:

• Temperature between 5°C and 40°C.
• Relative humidity of less than 85%, preferably between 10:00 and 16:00.
• Ideally apply when the temperature of the substrate is at least 2°C above dew point. If possible away from direct sunlight.

Drying time:
Touch dry – 30 minutes at 23°C.
Note: Higher temperatures will accelerate the drying times (approximately halved for every 10°C increase), whilst lower temperatures will retard the drying time (approximately doubled for every 10°C decrease).

Recoating time:
4 hours at 23°C.

Requirements:
Two coats.

Surface Preparations
Cement plaster:

• Direct – no primer required.

Gypsum ceiling boards:

• Prime with one coat of Prominent Dampcure or Prominent Plaster Primer or Prominent Trade Plaster Primer.

Ceilings:

• Sand to a matt finish, remove dust, clean with ProGold General Purpose Cleaner diluted (1:10) with water, rinse with clean water and apply directly.

Not recommended as final coat on other surfaces.

Limitations

• Not recommended as a finishing coat due to poor wearing -and stain resistance.
• Not to be used directly on rhinolite, cretestone and parapet walls.
• Cannot be applied in cold and moist conditions.
• Product cannot accommodate excessive movement, i.e. hairline cracking, etc.
• Not to be used in bathrooms and kitchens.
• Tinting not recommended.

Safety

• Keep out of reach of children.
• Ensure to maintain good ventilation during application and drying process.
• In case of skin contact, wash with soap and water or a recognised skin cleaner. Avoid contact with eyes. In case of contact with eyes rinse immediately with running water and seek medical advice.
• If product is ingested drink plenty of water or milk. Do not induce vomiting at any time. Seek medical advice.
• Refer to the Material Safety Data Sheet (MSDS) for detailed information about the product and transportation and classification criteria. MSDS is available on www.prominentpaints.co.za or from Prominent Customer Service Department.
• To avoid any risk of spillage, always transport in a secure upright position.

• Keep out of reach of children.
• Ensure to maintain good ventilation during application and drying process.
• In case of skin contact, wash with soap and water or a recognised skin cleaner. Avoid contact with eyes. In case of contact with eyes rinse immediately with running water and seek medical advice.
• If product is ingested drink plenty of water or milk. Do not induce vomiting at any time. Seek medical advice.
• Refer to the Material Safety Data Sheet (MSDS) for detailed information about the product and transportation and classification criteria. MSDS is available on www.prominentpaints.co.za or from Prominent Customer Service Department.
• To avoid any risk of spillage, always transport in a secure upright position.